TIIOCTI packing bags in cartons stacked in the warehouse where damp air collects

Which Lines on a Packing Spec Actually Stop Mould and Odour?

Built from a stored-bag moisture and odour prevention file and the packing clauses buyers keep rewriting.

by Nick Lee·8 min read·2026-10-05

Built from a stored-bag moisture and odour prevention file and the packing clauses buyers keep rewriting.

A purchase order for 20,000 jute shoppers arrived at the factory with a packing section that ran to eleven lines. Ten of them described carton dimensions, label placement and pallet height. The eleventh read: "Goods must be dry and free from odour." The buyer had signed it, the merchandiser had filed it, and nobody could say what it required anyone to do.

That sentence is where most mould claims begin. A musty smell in a delivered shipment is one of the most expensive quality complaints a supplier can face, because it cannot be inspected out at the destination. The goods have arrived, the odour is in the fibre, and the container has already crossed an ocean. The problem itself was created days or weeks before loading, in conditions that nobody thought to record.

The fix is not a better adjective. It is a set of lines that name a number, a time, a room and a record. Here is how those lines read when they are written to be enforced.

The Line That Reads Dry But Says Nothing

A hand presses a black measuring gauge onto tan burlap fabric beside a white plastic tub lid.

“Free from moisture” is a wish, not a specification. It gives an inspector nothing to measure and a factory nothing to aim at. Natural fibre bags are the most exposed category because the fibre itself holds water. A jute or cotton bag that feels dry to the hand can still carry enough water to support microbial growth once it sits in a sealed carton for a few weeks.

The word “dry” also hides where moisture actually enters. Four sources account for most problems: fabric that has not fully dried after finishing or washing; cartons assembled or stored in a humid environment, which carry damp air into the pack; packing in a warehouse without humidity control, particularly in coastal or monsoon regions; and condensation that forms inside cartons or containers when warm, moist air cools.

A spec line that says “dry” touches none of these. A spec line that names a moisture figure, a packing window, a humidity ceiling and an inner packing method touches all four. The rest of this page takes those lines one at a time.

Moisture Content: Write a Number, Not an Adjective

A printed sheet lies on a speckled stone bench beside a stack of white padded envelopes.

The first enforceable line is a moisture content for finished goods, stated as a percentage and tied to a test method. Without a figure, the factory cannot know when drying is finished, and the buyer cannot reject a batch that reads slightly high.

The number matters because the failure mode is invisible. Microbial activity in damp textile material produces odour compounds well before visible mould colonies develop. By the time a buyer sees spots on a bag, the problem has been developing for some time. A reading taken at packing catches the batch while it can still be dried and repacked.

How to verify: ask for the reading to be taken on finished goods, not on incoming fabric, and recorded against the order number. A handheld moisture meter gives a fast pass or fail at the packing table. The exact acceptable range depends on fibre and finish, so the spec should carry the figure the buyer and factory agreed, not a generic one copied from another programme.

The line to write: “Moisture content of finished bags not to exceed [agreed figure] per cent, measured on [agreed method], recorded per batch before packing.”

Packing Window: Hours After Finishing, Not Weeks

Timing is the control that gets skipped when a factory is busy. Finished bags should be packed promptly and shipped on schedule rather than stored for extended periods in uncontrolled space. A bag that sits for three months through a humid season accumulates moisture no drying room can undo.

The spec should state a window in hours or days between finishing and packing, and a second window between packing and container loading. Both are short. Both are checkable from production and shipping records the factory already keeps.

How to verify: compare the finishing date on the batch card with the packing date on the carton label. A gap that runs into weeks is a flag, even if the bags look fine. Where a delay is unavoidable, the batch should go back through a dry, controlled space rather than sit on an open floor.

Humidity Control: The Clause That Names a Room

Tan hessian sacks are stacked in rows on wooden pallets inside a bright warehouse with tall windows.

“Store in a dry place” is the most common humidity line and the least useful. It does not name a room, a reading or a person responsible. The clause that works names the packing area and sets a ceiling.

EPA indoor air quality guidance on moisture and mould sets a practical threshold: keep indoor relative humidity below 60 per cent, and ideally between 30 and 50 per cent, and mould does not establish itself. A packing hall that holds those figures through a monsoon week is doing something different from one that holds them in February.

Air movement matters as much as the number. Stagnant air allows moisture to accumulate in the microclimate around a stack, so bags stacked against a wall or under a leaking roof can spoil while the room itself reads acceptable. The clause should cover both the reading and the airflow around stored goods.

How to verify: ask for a humidity log from the packing area covering the production dates, and check that the goods were stacked clear of walls with air able to move around the pallets.

Inner Packing: Polybag, Bundle or Nothing

Gloved hands adjust a clear-wrapped tan fabric bag inside an open cardboard box with cartons behind.

Inner packing is the last line of defence. Polybagging individual bags, or bundling in tens inside a sealed inner bag, limits the spread of moisture from one damp unit to the whole carton. Without it, a single wet bag can seed an entire shipment.

This line is a decision, not a default. Polybag per unit costs more in material and labour. Bundling in tens is cheaper and still contains a local problem. Loose packing in the carton gives moisture a free path. Packing mode should be agreed before production, because the choice changes the carton count, the packing time and the freight profile.

How to verify: the pre-shipment check should open cartons from the top, middle and bottom of a pallet and confirm the inner packing matches the agreed method. A carton that was packed loose when the order specified bundles is a spec breach even if the bags are dry.

Desiccant and Vent Holes: Two Lines That Cut Both Ways

Desiccants help where the route or the storage conditions justify them, provided they are sized for the volume and the journey. An undersized sachet in a large carton absorbs very little and creates a false sense of protection. The spec should either name a sizing rule tied to carton volume and transit length, or leave desiccant out rather than add it as decoration.

Carton ventilation is the line most often copied from a house standard without thinking. Ventilation openings let a carton breathe, which is useful in dry conditions and counterproductive in humid ones. A vented carton moving through a humid port draws moist air straight to the goods. The choice should follow the route and season, so the spec needs a conditional line rather than a fixed one.

How to verify: check the carton sample against the route. A vented carton on a humid lane, or a desiccant sachet sized for a carton half its volume, should be corrected before the run starts, not at the loading bay.

The Odour Check Nobody Writes Into the Order

A worker in a white coat opens a burlap sack to inspect loose pale filling beside stacked sacks.

The sense of smell is a legitimate inspection tool at the factory, and it is almost never written into a purchase order. A carton that smells musty when opened should be investigated rather than shipped, even if the bags inside look perfect. The nose catches the problem weeks before the eye does.

Smell also survives when appearance is corrected. Washing or wiping a damp bag may remove visible mould and leave the odour in the fibre, which is the version of the problem that generates claims at the destination. A factory that only inspects surfaces will pass a batch that a buyer will reject on opening.

The line to write is short: “Odour check on opening, recorded per carton sampled, against the order.” It costs a few minutes per carton and turns a subjective complaint into a recorded observation.

What a Pre-Shipment Record Should Show

Two checks before packing catch most problems, and both belong in the pre-shipment inspection routine alongside the physical checks. The first is a moisture reading on finished goods, recorded against the order, which turns a subjective judgement into a number. The second is a smell check when a carton is opened, which is quick and needs no equipment.

The record should also show the packing date against the finishing date, the humidity log for the packing area, and photographs of the inner packing as opened. Cartons counted and photographed before the container seals give the buyer a dated reference for what left the workshop. Where a discrepancy is found, the resolution is to dry and repack rather than to ship and hope, and the cost difference between those two paths is usually a fraction of a claim.

Five requirements make storage problems rare: a stated moisture content for finished goods, packing within a defined window after finishing, humidity control in the packing area, inner packing appropriate to the route, and a moisture and odour check recorded before the container is sealed. Where a programme ships natural fibre bags through humid seasons, these requirements are worth writing into the purchase order rather than discussing as preferences.

The line that reads “dry and free from odour” is the one that gets missed, because it looks like a requirement and behaves like a hope. Replace it with a number, a window, a room and a record, and the carton that arrives smelling of jute smells of jute.

FAQ

Why do natural fibre bags smell musty when the carton looks fine on arrival?

Usually because moisture was present in the fibre or the packing, and microbial activity developed during storage or transit, producing odour before any visible mould. The carton exterior can look perfect while the fibre inside carries the problem.

What relative humidity should a packing area stay under?

EPA guidance keeps relative humidity below 60 per cent, ideally between 30 and 50 per cent, which prevents mould establishing itself. The spec should name the packing area and require a log covering the production dates.

Do desiccant sachets fix a damp carton?

They help when sized for the carton volume and journey length. Undersized desiccants provide little protection and create false confidence, so the spec needs a sizing rule or no desiccant line at all.

Should cartons have ventilation holes?

It depends on the route. Ventilation helps in dry conditions and works against you in humid ones, so the choice should follow the shipment and season rather than a single house standard.

Discuss your bag project
Start a quote→
WhatsApp