TIIOCTI insulated delivery bags loaded in a cold chain van

Why Did the Ice Melt Early in Your Insulated Delivery Bag?

Reorganised from an archived insulated bag foam thickness article, with product spec data on PE foam and foil lining.

by Nick Lee·6 min read·2026-08-21

Reorganised from an archived insulated bag foam thickness article, with product spec data on PE foam and foil lining.

The cartons came back on a Tuesday morning, stacked by the loading door with water stains on the bottom edges. Inside, the ice packs had gone soft and the chilled cargo was written off before anyone opened the second box. The route had been a normal summer run, and the bags had been bought as insulated delivery bags.

Three foam samples sat on the buyer’s desk that week: a 2 mm sheet, a 3 mm sheet and a 5 mm sheet, each cut from a different quoted build. The buyer had approved the cheapest one because the swatches felt similar through the outer fabric. That decision is where the story starts, and it is not really about the feel of foam.

The Cartons That Came Back Warm

An open cardboard box of silver foil pouches sits before stacked cartons outside a warehouse dock.

The delivery left the depot at 7 a.m. with the bags packed at their intended cargo ratio, ice packs laid in, lids zipped. By early afternoon the interior temperature had climbed past the point where the chilled goods were safe, and the receiving team rejected the load.

Nobody on the dock could say why. The bags looked right, the seams were straight, and the print matched the approved artwork. The failure was invisible from the outside, which is why the buyer sent the samples back for a second look rather than blaming the driver.

The first question asked was about the foam. The second was about the closure. The third, and the one that actually explained the gap, was about how much ice had been packed against how much wall.

Rewinding to the Wall That Was Specified

Two white insulated delivery bags lie flat on a worn metal surface.

The purchase order listed “insulated lining” and a bag size, and nothing else. That phrase can cover a 2 mm wall or an 8 mm wall, and the factory built to the lower end because the order did not push it higher.

A delivery of insulated bags can hold temperature for 12 hours or lose it in 3, and the deciding spec is one number: foam thickness. The buyer had assumed the word “insulated” carried a number with it. It does not.

The quoted build used EPE foam inside a five-layer wall. The layers are outer fabric, EPE foam, a radiant barrier, a PE film and an inner lining, and the foam is the layer that moves hold time most. When the thickness is left open, the whole stack is left open.

Where the Hours Leaked Out

A white insulated bag with a fabric handle lies on a scuffed workbench, more bags behind.

Two leaks showed up once the bags were opened. The first was the foam itself: a 2 mm wall holds cold for 3 to 4 hours at 25 to 30 degrees ambient, which suits a lunch run or a 30-minute last-mile drop and not a full afternoon route.

The second leak was at the opening. A wall is only as good as its closure, and stitched closures leak at every needle hole, losing 15 to 25 percent of theoretical hold time. The returned bags had stitching running through the inner lining, so the cold air had a path out that no amount of foam could close.

A third leak was quieter. The cross section showed crushed corners where the foam had been folded during assembly, and gaps at those corners leak disproportionately. The wall was continuous on the flat panels and broken where the bag actually gets handled.

The Cross Section That Explains the Gap

An open grey fabric bag reveals a foil lining behind stacked foam insulation panels.

Cut one returned bag open and the layers read like a spec sheet: fabric, foam, foil, film, lining. Each layer has a job, and each one has to run without a break from seam to seam.

The foil is a radiant barrier that reflects 95 percent or more of radiant heat, and the PE film seals the foam against moisture and ice melt. Skip the foil and the bag loses 2 to 3 hours even with the foam intact, because conduction and radiation are separate problems.

The buyer’s returned bags had foil, but it stopped short at the base seam. That short stop is the kind of detail a photo of the outside will never show, and it is why a cutaway sample belongs in the approval file before the bulk order is placed.

Volume, Ice Load and the Ratio Nobody Writes Down

The route also carried a second bag size, a larger one, and the buyer assumed the bigger bag would hold cold longer. It did not. Hold time depends on the ice-to-surface ratio, not on the wall alone.

A 6 to 20 liter bag at 3 mm often outperforms a 40 liter bag at 5 mm on the same run, because the small bag packs more ice per square centimeter of wall. The large bag had more surface to protect and less ice pressed against each panel.

That ratio is rarely written on a purchase order, and it should be. The number to agree is how much ice goes in per liter of cargo, because a bag specified for a full load and packed half full behaves like a thinner bag.

The Ice Test That Settles the Argument

A white insulated bag with black trim lies open on a table, a digital thermometer inside.

Every quoted hold time can be checked with the same simple test before an order ships. Pack the sample bag at its intended cargo ratio with a known ice load, place a logger reading to 0.5 degrees inside, and record the interior temperature curve against ambient for 12 hours at 25 to 30 degrees.

Then repeat the run at 35 to 40 degrees for summer routes. The second curve is the one that matters for a July delivery, and it is the curve the buyer never had on the first order.

A factory that declines to run the test on a production sample is declining to stand behind its own spec sheet. The test costs little, uses the same bag that will ship, and turns a range on a page into a number the buyer can defend to a customer.

What to Write on the Purchase Order

The fix on the second order was a rewritten spec line, not a new supplier. The buyer specified the hold time and the ambient condition first, then let the wall build backward from it: 3, 5 or 8 mm, foil included, closures sealed, volume sized to the cargo.

For 8 hours of cold at 25 to 30 degrees ambient, 5 mm EPE in the five-layer wall reaches 8 to 10 hours. Summer routes move to 8 mm or add gel packs, and the closure gets heat-sealed on the inner lining with stitching confined to the outside.

The rewritten order also carried four checks a buyer can run without a lab. Ask for a cutaway sample and confirm all five layers run unbroken. Confirm the closure type in writing. State the ice-to-cargo ratio for each bag size. Require the 12-hour logger curve at both ambient ranges before shipment.

FAQ

What foam thickness does the buyer need for 8 hours of cold?

A 5 mm EPE wall inside the five-layer build holds 8 to 10 hours at 25 to 30 degrees ambient. Move to 8 mm or add gel packs when the route runs through summer heat above that range.

Does the aluminum foil layer or the foam matter more?

Both, and they do different jobs. Foam blocks conduction, while the foil reflects over 95 percent of radiant heat. Dropping the foil costs 2 to 3 hours even when the foam thickness is unchanged.

Why does a small cooler bag outlast a large one?

The ice-to-surface ratio decides it. A bag under 20 liters at 3 mm often beats a 40 liter bag at 5 mm on the same run, because the smaller walls see less melt per liter of ice packed against them.

Can a factory run the ice test on a production sample?

Yes, and the test should use the bag that will actually ship. Pack it at the intended cargo ratio, log the interior temperature for 12 hours at 25 to 30 degrees, then repeat at 35 to 40 degrees for summer routes.

Discuss your bag project
Start a quote→
WhatsApp